
Mains dimming
Mains dimming in Cork
Mains dimming controls a light by trimming the mains supply that feeds the fitting, which is how most homes in Cork are dimmed. Cork Lighting designs mains dimming so the dimmers, the fittings and the loads are matched, because that match decides whether a light fades smoothly or flickers and hums.
Mains dimming that works with modern LED
Mains dimming does not need a separate control cable, which is why it is so common. The catch is that LED fittings behave very differently from the filament bulbs older dimmers were built for, so the dimmer and the lamp have to be chosen together.
Leading and trailing edge
Different dimmers cut the mains in different ways, and the right type depends on the driver in the fitting.
Minimum load
Some dimmers need a minimum load to behave, which matters when a circuit has only a few low power LED fittings.
Compatible fittings
We check that the LED fittings are rated as dimmable and that the driver suits the dimmer.
Dimmer modules in a panel
Instead of dimmers behind every switch, a central panel can hold the dimming modules, with simple keypads on the walls.
Whole house scenes
Mains dimmed circuits sit in the same scenes as the rest of the lighting, so one button can set the whole room.
Replacing old dimmers
Old dimmers that buzz, flicker or no longer reach low levels can be replaced with better matched ones.
Local to you
Mains dimming problems we see in Cork homes
Many Cork houses have had their halogen downlights swapped for LED over the years, and the original dimmers have been left in place. The result is lights that flicker at low levels, switch off when dimmed too far, or hum. Often the fix is a better matched dimmer rather than new fittings.
For a new build or renovation we plan mains dimming from the start, so the fittings, the circuits and the controls are chosen together. We list what is on each circuit and size the dimmer module to the load.
See the areas we cover in Cork, or go straight to Douglas, Ballincollig, Kinsale.
What a mains dimming job includes
- A check of the fittings. Dimmable rating and driver type confirmed for each circuit.
- A dimmer matched to the load. Chosen for the type and the number of fittings.
- Compliant fixed wiring. New or altered circuits installed and certified by a registered electrician, arranged by us.
- Low level tuning. Minimum levels set so fittings fade without flicker or shutting off.
Fixed lighting circuits in Irish homes are wired to the National Rules for Electrical Installations published by the Electro-Technical Council of Ireland.
Fixture compatibility
Will your fitting dim properly?
Mains dimming depends on the fitting and the dimmer agreeing with each other. For Crestron systems we check the fitting against Crestron's lighting fixture compatibility list before it is ordered.
Look up the Lighting Fixture Compatibility List on Crestron's support site before you buy fittings.
Related services
More from Cork Lighting
Mains switched lightingReliable on and off control, tied into the same scenes.
DALI lighting controlAddressable digital dimming for each fitting or group of fittings.
Circadian lightingTunable white lighting that follows the day.
Lighting designRoom by room layouts, circuit schedules and control plans.
Lighting installationFirst fix cabling to commissioning, by one team.
Lighting control systemsCrestron first, with Lutron, Control4, Rako, iLight and C-Bus too.Questions we are often asked
Why do my LED lights flicker when dimmed?
Usually the dimmer and the LED driver are a poor match. A better matched dimmer, or better fittings, normally cures it.
Can I put an LED bulb on my old dimmer?
Sometimes, but old dimmers were built for filament bulbs and may flicker or hum with LED. We check each circuit.
Do I need to replace all my fittings to dim them smoothly?
Not always. If the fittings are rated as dimmable, a well matched dimmer is often enough.
Is mains dimming the same as smart dimming?
Mains dimming is the method of dimming. Smart control adds scenes, keypads and an app, and it can use mains dimming underneath.
Do I need an electrician for a new dimmer?
A like for like swap can be simple, but anything that changes the fixed wiring should be done and certified by a registered electrician, and we arrange that.
Want advice on mains dimming in Cork? Call 021 202 8107 or send the details through our contact form and we will arrange a consultation.