Skip to main content
Crestron DIN rail lighting: wall mounted touch panel beside a keypad in a marble floored hall

Crestron DIN rail lighting

Crestron DIN rail lighting in Cork

Crestron DIN rail lighting puts all of a home's lighting control into a tidy central panel, with every circuit wired back to one cabinet. Cork Lighting draws, builds and commissions these panels for Cork homes, so the electrician knows what to run and the lights behave when the house is finished.

Crestron DIN rail lighting panels for Cork houses

A DIN rail panel is a cabinet where switching, dimming, 0 to 10 volt and DALI modules are clipped onto rails, much like a consumer unit. Every lighting cable in the house comes back to it, which keeps the walls simple and puts all the electronics in one place that is easy to service.

Switching modules

Relay modules for circuits that only need on and off, such as plant rooms, utility spaces and outdoor lighting.

Mains dimming modules

Dimmer modules for compatible dimmable fittings on the mains, with the smooth fade you expect from a good lighting scheme.

0 to 10 volt modules

Controllers for LED fittings with 0 to 10 volt drivers, which are common in architectural and linear lighting.

DALI controllers

Modules that talk to DALI fittings, which suits large schemes and fittings that can be addressed one at a time.

Power and protection

Power supplies and protective devices sized for the load, with space left on the rail for later additions.

Clear labelling

Every circuit is labelled to match the lighting schedule and the keypads, so any electrician can follow it years later.

Crestron lighting panels we have built

Crestron DIN rail lighting modules

DIN-8SWU8 universal switch

An eight channel relay switch module that handles standard switching and bi-directional motor control.

DIN-4DIMU4 universal dimmer

A four channel dimmer for LED, MLV, ELV, incandescent, fluorescent and motor loads, with a minimum load of zero watts.

Compact rail space

Each module takes 6M of rail, which Crestron describes as its most compact switching and dimming form factor.

Spring terminals

Terminals take 12 AWG passthrough connections on live and switched live, which keeps panel wiring tidy.

Module to module link

M2M connectivity joins the modules in a panel without Cresnet communication or override cabling between them.

Set up on the front

Front panel RGB LEDs allow on site configuration without a laptop, and the modules run alone or in Crestron Home.

Local to you

Lighting panels for new builds and renovations around Cork

A central panel suits new builds and deep renovations around Cork, where cables can be pulled back to one point before the plaster goes on. It is also a sensible choice for a house with a lot of lighting, because everything stays reachable instead of being hidden behind switches throughout the house.

Panels are drawn up by 1Install before first fix, with the terminals, modules and power supplies shown to scale. Your electrician receives a cable schedule listing each circuit and the wire it needs, which avoids guesswork on site.

See the areas we cover in Cork, or go straight to Douglas, Ballincollig, Kinsale.

What a 1Install lighting panel gives you

  • A drawing before anything is bought. The panel layout, module count and spare capacity agreed on paper first.
  • A cable schedule for the electrician. Each circuit, cable type and destination listed room by room.
  • Tidy, serviceable wiring. Terminals, labels and cable routes laid out so a future engineer finds everything quickly.
  • Room to grow. Spare rail and spare module slots left so a new circuit does not mean rebuilding the panel.

Crestron makes DIN rail modules for switched, dimmed, 0 to 10 volt and DALI lighting, listed by Crestron, which lets one panel serve every type of fitting in the house.

Fixture compatibility

Dimmer and driver choices checked against the list

In a DIN rail panel the dimmer is chosen for the load it feeds. We use Crestron's lighting fixture compatibility list to confirm that the fittings you have chosen work with the dimmers in the panel.

Open the Lighting Fixture Compatibility List from Crestron, and send us the fittings you like.

Lifetime warranty

Lifetime warranty on DIN rail lighting panels

Crestron's limited lifetime warranty covers the dimmers, power supplies and control processors that sit in a DIN rail lighting panel, so the cabinet we build for you is protected long after handover.

  • Panel components covered. Dimmers, power supplies and processors in the cabinet are within the lifetime warranty.
  • Reseller built. The panel must be supplied and installed through an authorised reseller, as ours are.
  • Remedy. A faulty covered module is repaired, replaced or credited by Crestron.
  • Breakers excluded. Circuit breakers, LED drivers and fittings are not part of the lifetime cover.

The full wording is in the Crestron lifetime warranty terms, published by Crestron Europe.

Questions we are often asked

What is a DIN rail lighting panel?

It is a cabinet with standard rails onto which lighting modules clip, the same style of mounting used in an electrical consumer unit. Each module controls a number of lighting circuits.

Why use a central panel instead of dimmers behind every switch?

A central panel keeps all the electronics in one serviceable place, supports all types of load and lets the walls carry only simple keypads. It is usually the neatest option in a new build.

How big is a lighting panel for a house?

It depends on the number of circuits and the load types. We size it from your lighting schedule and leave spare capacity for additions.

Where does the panel go?

Usually a utility room, plant room, understairs cupboard or garage, somewhere ventilated that is easy to reach but out of sight.

Can one panel control mains dimmed, 0 to 10 volt and DALI lights together?

Yes. Different module types can sit in the same cabinet, so each type of fitting in the house gets the control it needs.

Want advice on Crestron DIN rail lighting in Cork? Call 021 202 8107 or send the details through our contact form and we will arrange a consultation.

Book a consultation

Tell us about your lighting

Tell us about the house and what you would like the lighting to do. Send your plans or a few photos if you have them, and we will arrange a consultation and follow it with a written, itemised quote.

  • Lighting designed before first fix
  • Crestron first, with every other main brand
  • Backed by 1Install, 19 years installing smart homes

Prefer to talk? 021 202 8107

What are you interested in?