Skip to main content
0-10V lighting control: open plan kitchen with lit ceiling coves, downlights and warm lighting under the cabinets

0 to 10 volt dimming

0-10V lighting control in Cork

0-10V lighting control, also called 0 to 10 volt dimming, uses a separate low voltage signal to tell an LED driver how bright to be. Cork Lighting plans 0-10V lighting control in Cork as part of a complete scheme, so linear lighting, coves and architectural fittings dim smoothly and behave the same from room to room.

How 0-10V lighting control works

A 0-10V fitting has two supplies: the mains feeds the driver, and a thin two core control cable carries a signal between zero and ten volts. The driver sets its output according to that voltage, so a controller can dim many fittings by sending one signal.

Smooth, flicker free dimming

Because the mains is not chopped to dim the light, a good 0-10V driver can fade very smoothly down to low levels.

Linear and architectural lighting

Cove lighting, shadow gaps, tape and linear fittings often use 0-10V drivers, and it is a common way to control them.

Separate control cable

Each group of fittings needs a low voltage control cable as well as its mains supply, so it has to be planned before first fix.

Groups, not single fittings

Fittings on the same control signal dim together, which suits runs of cove lighting but is less flexible than addressable systems.

Mains switching for off

Many drivers still use a little power at zero volts, so a relay is commonly used to switch them off completely.

Fits into a bigger system

A lighting panel with 0-10V outputs can run these circuits alongside mains dimmed and DALI circuits from the same keypads.

Local to you

0-10V lighting for homes around Cork

Cork homes with generous open plan spaces, vaulted ceilings and modern kitchens often use runs of linear and cove lighting. Those are the places where 0-10V earns its keep, because a clean dimming curve makes a long run of light look even.

We decide with you and your electrician at design stage which circuits are 0-10V, because the driver choice and the control cable have to be settled before the plaster goes on. Changing a driver afterwards is much more work than picking the right one first.

See the areas we cover in Cork, or go straight to Douglas, Ballincollig, Kinsale.

What a 0-10V lighting control job includes

  • A driver and control match. Drivers chosen to suit the controller and the fittings.
  • A control cable schedule. Cables and routes listed for each group of fittings.
  • Relay switching where needed. Fittings that must turn fully off are on a switched supply.
  • Tuning in the finished room. Minimum and maximum levels set so every run looks even.

The low voltage control interface behind 0-10V dimming sits in the lighting standards family maintained by the International Electrotechnical Commission.

Fixture compatibility

Checking a 0-10V driver with Crestron

A 0-10V fitting still has to behave on the control system it is wired to. Crestron's lighting fixture compatibility list is one of the references we check before specifying drivers and fittings.

Read the Lighting Fixture Compatibility List on Crestron's site for fittings on Crestron systems.

Questions we are often asked

What does 0 to 10 volt dimming mean?

It is a way of dimming LED drivers with a low voltage signal. Zero volts is the lowest light output and ten volts is full output.

Do I need a special cable for 0-10V dimming?

Yes. A two core low voltage control cable runs to each group of drivers, alongside the mains supply.

Can 0-10V and mains dimmed lights be on the same keypad?

Yes. A central lighting panel can control both types, so one keypad can set scenes for every fitting in a room.

Is 0-10V better than DALI?

Neither is better in every case. 0-10V is simple and common, and DALI allows each fitting to be addressed. We choose by the fittings and the design.

Can I add 0-10V to an existing house?

It is easiest at first fix. In a finished house we can sometimes run a control cable where lights are being replaced, and we check before recommending it.

Want advice on 0-10V lighting control in Cork? Call 021 202 8107 or send the details through our contact form and we will arrange a consultation.

Book a consultation

Tell us about your lighting

Tell us about the house and what you would like the lighting to do. Send your plans or a few photos if you have them, and we will arrange a consultation and follow it with a written, itemised quote.

  • Lighting designed before first fix
  • Crestron first, with every other main brand
  • Backed by 1Install, 19 years installing smart homes

Prefer to talk? 021 202 8107

What are you interested in?